View NCP694HSAN33T1G_4653601.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

NCP694 1A CMOS Low-Dropout Voltage Regulator
The NCP694 series of fixed output super low dropout linear regulators are designed for portable battery powered applications with high output current requirement up to 1 A and -3 mV typical load regulation at 1 A. Each device contains a voltage reference unit, an error amplifier, a PMOS power transistor, resistors for setting output voltage, a current limit circuits for overcurrent and thermal-shutdown. A standby mode with ultra low supply current can be realized with the chip enable function. The device is housed in the SOT-89-5 and HSON-6 packages. Standard voltage versions are 0.8 V, 1.0 V, 1.2 V, 2.5 V, 3.3 V for fixed version and adjustable output voltage down to 1.0 V.
Features http://onsemi.com MARKING DIAGRAMS
1 SOT-89-5 CASE 528AB XXX XMM G 6 6 1 HSON-6 CASE 506AE XXX XYYG 1
* Maximum Operating Voltage of 6.0 V * Minimum Output Voltage Down to 0.8 V for Fix Version and 1.0 V * * * * * * * * *
for Adjustable Version Load Regulation -3 mV at 1 A Output Current Low Dropout Build-in Auto Discharge Function for D Version Standby Mode With Low Consumption These are Pb-Free Devices Battery Powered Instruments Hand-Held Instruments Camcorders and Cameras Portable communication equipments
Typical Applications
XXXX = Specific Device Code MM, YY = Lot Number G or G = Pb-Free Package For actual marking Pb-Free indicator, "G" or microdot "G" may or may not be provided.
ORDERING INFORMATION
See detailed ordering and shipping information in the package dimensions section on page 15 of this data sheet.
(c) Semiconductor Components Industries, LLC, 2010
January, 2010 - Rev. 1
1
Publication Order Number: NCP694/D
NCP694
654 HSON-6 123 (TOP VIEW) 5 4 321 (BOTTOM VIEW) 4 5 456
SOT-89-5
1
2 3 (TOP VIEW)
Figure 1. Pin Description
3 2 1 (BOTTOM VIEW)
PIN FUNCTION DESCRIPTION FOR SOT-89-5 PACKAGE
Pin No. 1 2 3 4 5 Pin Name ADJ/NC GND CE Vin Vout Description Adjust pin for NCP694DADJHT1G and NCP694HADJHT1G / No connection Power supply ground This input is used to place the device into low-power standby. When this input is pulled low, the device is disabled. If this function is not used, Enable should be connected to Vin. Positive power supply input voltage. Regulated output voltage.
PIN FUNCTION DESCRIPTION FOR HSON-6 PACKAGE
Pin No. 1 2 3 4 5 6 Pin Name Vout Vout ADJ / NC GND CE Vin Regulated output voltage Regulated output voltage Adjust pin for NCP694DSANADJT1G and NCP694HSANADJT1G / No connection Power supply ground This input is used to place the device into low power standby. When this input is pulled low, the device is disabled. If this function is not used, Enable should be connected to Vin. Positive power supply input voltage Description
Vin Vin
Vout Vout
Vin Vin
Vout Vout
Vref
Vref
CE
Current Limit& Thermal Shutdown GND
CE
Current Limit & Thermal Shutdown GND
Version H (NCP694HxxxxT1G)
Figure 2. Internal Block Diagram http://onsemi.com
2
Version D (NCP694DxxxxT1G)
NCP694
MAXIMUM RATINGS
Rating Input Voltage Enable Voltage Output Voltage Power Dissipation SOT-89-5 Power Dissipation HSON-6 Operating Junction Temperature Operating Ambient Temperature Storage Temperature Symbol Vin VCE Vout PD PD TJ TA Tstg Value 6.5 -0.3 to Vin -0.3 to Vin + 0.3 900 900 +150 -40 to +85 -55 to +125 Unit V V V mW mW C C C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. This device series contains ESD protection and exceeds the following tests: Human Body Model 2000 V per JEDEC Machine Model Method 200 V
THERMAL CHARACTERISTICS
Rating Junction-to-Ambient SOT-89-5 Power Dissipation SOT-89-5 Junction-to-Ambient HSON-6 Power Dissipation HSON-6 NOTE: Symbol RqJA PD RqJA PD 1 oz Copper Thickness, 100 mm2 Test Conditions 1 oz Copper Thickness, 100 mm2 Typical Value 111 900 111 900 Unit C/W mW C/W mW
Single component mounted on an 80 x 80 x 1.5 mm FR4 PCB with stated copper head spreading area. Using the following boundary conditions as stated in EIA/JESD 51-1, 2, 3, 7, 12.
http://onsemi.com
3
NCP694
ELECTRICAL CHARACTERISTICS FOR FIX VERSION (Vin = Vout(nom.) + 1.0 V, VCE = Vin, Cin = 4.7 mF, Cout = 4.7 mF, TA =
25C, unless otherwise noted) Characteristic Output Voltage (TA = 25C, Iout = 100 mA, Vin-Vout = 1 V) 0.8 V 1.0 V 1.2 V 2.5 V 3.3 V Output Current (Vin-Vout = 1 V) Input voltage Line Regulation (Iout = 100 mA) Load Regulation (Iout = 1 mA to 300 mA, Vin = Vout + 2.0 V) Load Regulation (Iout = 1 mA to 1 A, Vin = Vout + 2.0 V) Supply Current (Iout = 0 A, (Vin - Vout) = 1 V, VCE = Vin) Standby Current (VCE = 0V, Vin = 6.0 V) Short Current Limit (Vout = 0 V) Output Voltage Temperature Coefficient Enable Input Threshold Voltage (Voltage Increasing, Output Turns On, Logic High) (Voltage Decreasing, Output Turns Off, Logic Low) Enable Pull-down Current Drop Output Voltage (TA = 25C, Iout = 300 mA) 0.8 V Output voltage Vout (V) 1.0 V 1.2 V 2.5 V 3.3 V Drop Output Voltage (TA = 25C, Iout = 1A) 0.8 V Output voltage Vout (V) 1.0 V 1.2 V 2.5 V 3.3 V Ripple Rejection (Ripple 200 mVpp, Iout =100 mA, f = 1 kHz) Output Noise (BW = 10 Hz to 100 kHz, Iout = 1 mA) Thermal Shutdown Temperature/Hysteresis RDS(on) of additional output transistor (D version only) Vin-Vout Symbol Vout Min 0.770 0.970 1.170 2.450 3.234 Typ 0.8 1.0 1.2 2.5 3.3 1 1.4 - -15 - 0.05 -2 -3 60 0.1 250 - 1.0 0 $100 - - 100 0.33 0.22 0.18 0.10 0.05 0.72 0.64 0.56 0.32 0.18 70 30 150/30 30 - 6 0.4 220 0.570 0.470 0.320 0.150 0.100 6.0 0.2 15 - 100 1.0 Max 0.830 1.030 1.030 2.550 3.366 Unit V
Iout Vin Regline Regload03 Regload1 Iss Istby Ish Tc VthCE
A V %/V mV mV mA mA mA ppm/C V
nA V
Vin-Vout
V
PSRR
Vnoise
dB mVrms C W
Tshd/Hyst RDS(on)
2. Maximum package power dissipation limits must be observed. 3. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.
http://onsemi.com
4
NCP694
ELECTRICAL CHARACTERISTIC FOR ADJUSTABLE VERSION (Vin = Vout + 1 V, VCE = Vin, Cin = Cout = 4.7 mF, TA
= 25C, unless otherwise noted) Characteristic Input Voltage Supply Current (Vout = VADJ, Vin = 2 V, VCE = Vin) Standby Current (Vin = 6.0 V, VCE = 0 V) Reference Voltage For Adjustable Voltage Regulator (Vout = VADJ, Vin = 2.0 V, Iout = 100 mA Output Voltage Range Output Current (Vout = VADJ, Vin = 2.0 V) Load Regulation (Vin = 1.4 V, 1 mA < Iout < 300 mA, Vout = VADJ) Load Regulation (Vin = 1.7 V, 1 mA < Iout < 1 A, Vout = VADJ) Dropout Voltage (Vout = VADJ, Iout = 300 mA) Dropout Voltage (Vout = VADJ, Iout = 1 A) Line regulation (Vout = VADJ, Iout = 100 mA, 1.5 V < Vin < 6.0 V PSRR ( f = 1 kHz, Vout = VADJ, Vin = 2.5 V, Iout = 100 mA, Input Ripple 0.5 Vpp) Output Voltage Temperature Coefficient (Iout = 100 mA, -40C < TJ < 85C) Short Current Limit (Vout = VADJ = 0) Enable Pull-down Current Enable Input Threshold Voltage (Voltage Increasing, Output Turns On, Logic High) (Voltage Decreasing, Output Turns Off, Logic Low) Thermal Shutdown Temperature/Hysteresis RDS(on) of additional output transistor (D version only) Symbol Vin ISS Istandby Vref Voutrange Iout Vout/Iout Vout/Iout Vdrop300 Vdrop1 Vout/Vin PSRR Vout/TJ Ilim ICE VthCE 1 0 0.97 1 1 -15 -2 -3 0.18 0.56 0.05 70 $100 250 100 - - 150/ 30 30 220 6 0.4 0.2 0.32 15 Min 1.4 60 0.1 1 Typ Max 6 100 1 1.03 Vin Unit V uA uA V V A mV mV V V %V dB ppm/C mA nA V
Tshdn/ Hyst RDS(on)
C W
http://onsemi.com
5
NCP694
APPLICATIONS INFORMATION A typical application circuit for the NCP694 series is shown in Figure 5, Typical Application Schematic.
Input Decoupling (C1)
Set external components, especially the output capacitor, as close as possible to the circuit, and make leads as short as possible.
Thermal
A 4.7 mF capacitor either ceramic or tantalum is recommended and should be connected as close as possible to the pins of NCP694 device. Higher values and lower ESR will improve the overall line transient response.
Output Decoupling (C2)
The minimum decoupling value is 4.7 mF and can be augmented to fulfill stringent load transient requirements. The regulator accepts ceramic chip capacitors as well as tantalum devices. If a tantalum capacitor is used, and its ESR is large, the loop oscillation may result. Because of this, select C2 carefully considering its frequency characteristics. Larger values improve noise rejection and load regulation transient response.
Enable Operation
As power across the NCP694 increases, it might become necessary to provide some thermal relief. The maximum power dissipation supported by the device is dependent upon board design and layout. Mounting pad configuration on the PCB, the board material, and also the ambient temperature effect the rate of temperature rise for the part. This is stating that when the NCP694 has good thermal conductivity through the PCB, the junction temperature will be relatively low with high power dissipation applications.
Output Voltage Setting of Adjustable Version.
The enable pin CE will turn on or off the regulator. These limits of threshold are covered in the electrical specification section of this data sheet. If the enable is not used then the pin should be connected to Vin. The D version devices (NCP694DxxxxT1G) have additional circuitry in order to reach the turn-off speed faster than normal type. When the mode is into standby with CE signal, auto discharge transistor turns on.
Hints
An external two resistors are required for setting desired output voltage as shows Figure 3. Output Voltage Setting. The equation for the output voltage is mentioned in equation below.
V out + V ref ) R1 @ I1 + V ref ) R1 @ I adj ) I2 + V ref ) R1 @ V ref R adj ) R1 @ V ref R2 + V ref @ 1 ) R1 R adj ) R1 R2 + 1.0 @ 1 ) R1 R adj ) R1 R2
(eq. 1)
Please be sure the Vin and GND lines are sufficiently wide. If their impedance is high, noise pickup or unstable operation may result.
Vout Radj, RESISTANCE (MW) R1 ADJ Iadj Radj GND R2 I2 I1 Vref = 1 V
For better accuracy, choosing R2 << Radj reduces the error given by ADJ pin consumption. The typical resistance Radj is showed in Figure 4. ADJ Pin Resistance
1.8 1.6 1.4 1.2 1.0 0.8
-50
-25
0
25
50
75
100
TJ, TEMPERATURE (C)
Figure 3. Output Voltage Setting
Figure 4. ADJ Pin Resistance vs. Temperature
http://onsemi.com
6
NCP694
NCP694DSAN08T1G Vin 6 Vin Vout 1 Vout
5 C1 4.7 mF 4
CE
Vout
2 C2
GND
NC
3
4.7 mF
GND
GND
Figure 5. Typical Application Schematic
http://onsemi.com
7
NCP694
TYPICAL CHARACTERISTICS
0.9 0.8
1.6 1.4 2.5 V OUTPUT VOLTAGE (V) 1.2 1.0 0.8 0.6 0.4 0.2
1.4
OUTPUT VOLTAGE (V)
0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 0.0 0.2 0.4 0.6 0.8
1.7 V
1.6 V Vin = 1.4 V
Vin = 3.5 V 2.5 V 3.0 V Vout = 1.5 V TA = 25C 0.2 0.4 0.6 0.8 1.0 1.2 1.4 OUTPUT CURRENT (A)
2.0 V
Vout = 0.8 V TA = 25C
1.0 1.2
0.0 0.0
OUTPUT CURRENT (A)
Figure 6. Output Voltage vs. Output Current
Figure 7. Output Voltage vs. Output Current
3.5 3.0
1.2
OUTPUT VOLTAGE (V)
2.5 2.0 1.5 1.0 0.5 0.0 0.0 0.2 0.4 0.6 0.8 1.0
OUTPUT VOLTAGE (V)
3.6 V
4.5 V Vin = 4.0 V
1.0 0.8 0.6 0.4 0.2 0.0
Vin = 1.4 V
1.6 V
2.5 V 2.0 V
Vout = 3.3 V TA = 25C
1.2 1.4 1.6
Vout = Vadj = 1.0 V TA = 25C
0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4
OUTPUT CURRENT (A)
OUTPUT CURRENT (A)
Figure 8. Output Voltage vs. Output Current
1.2 1.0 OUTPUT VOLTAGE (V) 0.8 0.6 0.4 0.2 0.0 Iout = 1 mA 50 mA 100 mA 300 mA 0.0 1.0 2.0 3.0 4.0 Vout = 0.8 V TA = 25C 5.0 6.0 OUTPUT VOLTAGE (V) 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 0.0
Figure 9. Output Voltage vs. Output Current for Adjustable Output
Iout = 1 mA 50 mA 100 mA 300 mA 1.0 2.0 3.0 4.0 Vout = 1.5 V TA = 25C 5.0 6.0
INPUT VOLTAGE (V)
INPUT VOLTAGE (V)
Figure 10. Output Voltage vs. Input Voltage
Figure 11. Output Voltage vs. Input Voltage
http://onsemi.com
8
NCP694
TYPICAL CHARACTERISTICS
3.5 3.0 SUPPLY CURRENT (mA) OUTPUT VOLTAGE (V) 2.5 2.0 1.5 1.0 0.5 0 0 1.0 Iout = 1 mA 50 mA 100 mA 300 mA 2.0 3.0 4.0 INPUT VOLTAGE (V) Vout = 3.3 V TA = 25C 5.0 6.0 70.0 60.0 50.0 40.0 30.0 20.0 10.0 0 0 1 2 3 4 Vout = 0.8 V Iout = 0 mA TA = 25C 5 6
INPUT VOLTAGE (V)
Figure 12. Output Voltage vs. Input Voltage
Figure 13. Supply Current vs. Input Voltage
70.0 60.0 SUPPLY CURRENT (mA) 50.0 40.0 30.0 20.0 10.0 0.0 0 1 2 3 4 Vout = 1.5 V Iout = 0 mA TA = 25C 5 6 SUPPLY CURRENT (mA)
70.0 60.0 50.0 40.0 30.0 20.0 10.0 0.0 0 1 2 3 4 Vout = 3.3 V Iout = 0 mA TA = 25C 5 6
INPUT VOLTAGE (V)
INPUT VOLTAGE (V)
Figure 14. Supply Current vs. Input Voltage
Figure 15. Supply Current vs. Input Voltage
0.820 0.815 OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (V) Vout = 0.8 V Iout = 0 mA -20.0 0.0 20.0 40.0 60.0 80.0 0.810 0.805 0.800 0.795 0.790 0.785 0.780 -40.0
1.520 1.510 1.500 1.490 1.480 1.470 -40.0
Vout = 1.5 V Iout = 0 mA -20.0 0.0 20.0 40.0 60.0 80.0
TEMPERATURE (C)
TEMPERATURE (C)
Figure 16. Output Voltage vs. Temperature
Figure 17. Output Voltage vs. Temperature
http://onsemi.com
9
NCP694
TYPICAL CHARACTERISTICS
3.302 3.301 DROPOUT VOLTAGE (V) OUTPUT VOLTAGE (V) 3.300 3.299 3.298 3.297 3.296 3.295 3.294 3.293 3.292 -40.0 -20.0 0.0 20.0 40.0 Vout = 3.3 V Iout = 0 mA 60.0 80.0 TEMPERATURE (C) 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 0.0 0.2 0.4 0.6 Vout = 0.8 V 25C -40C TA = 85C
0.8
1.0
OUTPUT CURRENT (A)
Figure 18. Output Voltage vs. Temperature
0.4 0.35 0.3 0.25 0.2 0.15 0.1 0.05 0 0 0.2 0.4 0.6 OUTPUT CURRENT (A) 25C -40C Vout = 1.5 V 0.8 1 TA = 85C DROPOUT VOLTAGE (V) DROPOUT VOLTAGE (V)
Figure 19. Dropout Voltage vs. Output Current
0.20 0.18 0.16 0.14 0.12 0.10 0.08 0.06 0.04 0.02 0.00 0.0 0.1 0.2
-40C 25C Vout = 3.3 V TA = 85C
0.3 0.4 0.5 0.6 0.7 OUTPUT CURRENT (A)
0.8
0.9
1.0
Figure 20. Dropout Voltage vs. Output Current
0.8 0.7 DROPOUT VOLTAGE (V) 0.6 0.5 0.4 0.3 0.2 0.1 0.0 0.0 0.2 -40C Vout = Vadj = 1 V 0.4 0.6 OUTPUT CURRENT (A) 0.8 1.0 25C TA = 85C DROPOUT VOLTAGE (V)
0.7 0.6 0.5 0.4 0.3 0.2 0.1 0
Figure 21. Dropout Voltage vs. Output Current
TA = 25C
Iout = 1 A
500 mA 100 mA
1 1.5 2 2.5 3 3.5 4 SET OUTPUT VOLTAGE (V) 4.5 5
Figure 22. Dropout Voltage vs. Output Current for Adjustable Output
Figure 23. Dropout Voltage vs. Set Output Voltage
http://onsemi.com
10
NCP694
TYPICAL CHARACTERISTICS
80 70 60 PSRR (dB) PSRR (dB) 50 40 30 20 10 0 0.1 Vout = 0.8 V Vin = 1.8 V + 0.5 VPP Modulation TA = 25C Cout = 4.7 mF 1.0 10.0 FREQUENCY (kHz) 100 Iout = 1 A Iout = 100 mA 90 80 70 60 50 40 30 20 10 0 0.1 Vout = 1.5 V Vin = 2.5 V + 0.5 VPP Modulation TA = 25C Cout = 4.7 mF 1.0 10.0 FREQUENCY (kHz) 100 Iout = 1 A Iout = 100 mA
Figure 24. PSRR vs. Frequency
90 80 70 60 PSRR (dB) 50 40 30 20 10 0 0.1 Vout = 3.3 V Vin = 4.3 V + 0.5 VPP Modulation TA = 25C Cout = 4.7 mF 1.0 10.0 FREQUENCY (kHz)
Figure 25. PSRR vs. Frequency
Iout = 100 mA Iout = 1 A
100
Figure 26. PSRR vs. Frequency
3.0 2.5 INPUT VOLTAGE (V) 2.0 1.5 1.0 0.5 0.0 -10 0 Vout = 0.8 V Vin = Step 1.8 to 2.8 V Tr = Tf = 5 ms Cout = 4.7 mF, Iout = 100 mA TA = 25C Input Voltage 0.84 0.83 0.82 0.81 0.80 Output Voltage 0.79 0.78 100 OUTPUT VOLTAGE (V)
10
20
30
40 50 TIME (ms)
60
70
80
90
Figure 27. Line Transient Response
http://onsemi.com
11
NCP694
TYPICAL CHARACTERISTICS
6.0 5.0 INPUT VOLTAGE (V) 4.0 3.0 2.0 1.0 0.0 -10 0 Vout = 3.3 V Vin = Step to 4.3 V to 5.3 V Tr = Tf = 5 ms, Cout = 4.7 mF Iout = 100 mA TA = 25C Input Voltage 3.320 3.315 3.310 3.305 3.300 Output Voltage 3.295 3.290 100 OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (V) OUTPUT VOLtAGE (V)
10
20
30
40
50
60
70
80
90
TIME (ms)
Figure 28. Input Transient Response
110 100 OUTPUT CURRENT (mA) 90 80 70 60 50 40 30 20 10 -10 0 10 20 30 40 50 60 TIME (ms) 70 80 90 Vout = 0.8 V Vin = 1.8 V Cout = 4.7 mF, Iout = Step 50 mA to 100 mA TA = 25C
0.88 0.87 0.86 0.85 0.84 Output Current Output Voltage 0.83 0.82 0.81 0.80 0.79 0.78 100
Figure 29. Load Transient Response
110 100 OUTPUT CURRENT (mA) 90 80 70 60 50 40 30 20 10 -10 0 10 20 30 40 50 60 TIME (ms) 70 80 90 Vout = 3.3 V Vin = 4.3 V Cout = 4.7 mF, Iout = Step 50 mA to 100 mA TA = 25C 3.37 3.36 3.35 3.34 3.33 Output Current Output Voltage 3.32 3.31 3.30 3.29 3.28 3.27 100
Figure 30. Load Transient Response
http://onsemi.com
12
NCP694
TYPICAL CHARACTERISTICS
Figure 31. Output Voltage vs. CE Pin Turn-On NCP694Dx08xx
Figure 32. Output Voltage vs. CE Pin Turn-On NCP694Dx33xx
http://onsemi.com
13
NCP694
TYPICAL CHARACTERISTICS
Figure 33. Output Voltage vs. CE Pin Turn-Off NCP694H08xxxx
Figure 34. Output Voltage vs. CE Pin Turn-Off NCP694D08xxxx
http://onsemi.com
14
NCP694
ORDERING INFORMATION
Device NCP694HADJHT1G NCP694H08HT1G NCP694H10HT1G NCP694H12HT1G NCP694H25HT1G NCP694H33HT1G NCP694DADJHT1G NCP694D08HT1G NCP694D10HT1G NCP694D12HT1G NCP694D25HT1G NCP694D33HT1G NCP694HSANADJT1G NCP694HSAN08T1G NCP694HSAN10T1G NCP694HSAN12T1G NCP694HSAN25T1G NCP694HSAN33T1G NCP694DSANADJT1G NCP694DSAN08T1G NCP694DSAN10T1G NCP694DSAN12T1G NCP694DSAN25T1G NCP694DSAN33T1G Nominal Output Voltage adj. 0.8 V 1.0 V 1.2 V 2.5 V 3.3 V adj. 0.8 V 1.0 V 1.2 V 2.5V 3.3 V adj. 0.8 V 1.0 V 1.2 V 2.5 V 3.3 V adj. 0.8 V 1.0 V 1.2 V 2.5 V 3.3 V Description Enable High Enable High Enable High Enable High Enable High Enable High Enable High - Auto discharge Enable High - Auto discharge Enable High - Auto discharge Enable High - Auto discharge Enable High - Auto discharge Enable High - Auto discharge Enable High Enable High Enable High Enable High Enable High Enable High Enable High - Auto discharge Enable High - Auto discharge Enable High - Auto discharge Enable High - Auto discharge Enable High - Auto discharge Enable High - Auto discharge Marking L00B L08B L10B L12B L25B L33B L00D L08D L10D L12D L25D L33D H00B H08B H10B H12B H25B H33B H00D H08D H10D H12D H25D H33D Package SOT-89-5 (Pb-Free) SOT-89-5 (Pb-Free) SOT-89-5 (Pb-Free) SOT-89-5 (Pb-Free) SOT-89-5 (Pb-Free) SOT-89-5 (Pb-Free) SOT-89-5 (Pb-Free) SOT-89-5 (Pb-Free) SOT-89-5 (Pb-Free) SOT-89-5 (Pb-Free) SOT-89-5 (Pb-Free) SOT-89-5 (Pb-Free) HSON-6 (Pb-Free) HSON-6 (Pb-Free) HSON-6 (Pb-Free) HSON-6 (Pb-Free) HSON-6 (Pb-Free) HSON-6 (Pb-Free) HSON-6 (Pb-Free) HSON-6 (Pb-Free) HSON-6 (Pb-Free) HSON-6 (Pb-Free) HSON-6 (Pb-Free) HSON-6 (Pb-Free) Shipping 1000 / Tape & Reel 1000 / Tape & Reel 1000 / Tape & Reel 1000 / Tape & Reel 1000 / Tape & Reel 1000 / Tape & Reel 1000 / Tape & Reel 1000 / Tape & Reel 1000 / Tape & Reel 1000 / Tape & Reel 1000 / Tape & Reel 1000 / Tape & Reel 3000 / Tape & Reel 3000 / Tape & Reel 3000 / Tape & Reel 3000 / Tape & Reel 3000 / Tape & Reel 3000 / Tape & Reel 3000 / Tape & Reel 3000 / Tape & Reel 3000 / Tape & Reel 3000 / Tape & Reel 3000 / Tape & Reel 3000 / Tape & Reel
For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D.
http://onsemi.com
15
NCP694
PACKAGE DIMENSIONS
SOT-89, 5 LEAD CASE 528AB-01 ISSUE O
D
NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. LEAD THICKNESS INCLUDES LEAD FINISH. 4. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. 5. DIMENSIONS L, L2, L3, L4, L5, AND H ARE MEASURED AT DATUM PLANE C. DIM A b b1 c D D2 E e H L L2 L3 L4 L5 MILLIMETERS MIN MAX 1.40 1.60 0.32 0.52 0.37 0.57 0.30 0.50 4.40 4.60 1.40 1.80 2.40 2.60 1.40 1.60 4.25 4.45 1.10 1.50 0.80 1.20 0.95 1.35 0.65 1.05 0.20 0.60
E
H
1
TOP VIEW
A
c 0.10 C
C
SIDE VIEW e b1 L
1 2
e b
3
L2
4X
RECOMMENDED MOUNTING FOOTPRINT*
0.57 1.75 1.50 4.65 1.65
2X
L5
5 4
2.79
0.45
L3
L4
D2 BOTTOM VIEW
1.30
1
2X
1.50
0.62
DIMENSIONS: MILLIMETERS
*For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
16
NCP694
PACKAGE DIMENSIONS
HSON-6 CASE 506AE-01 ISSUE A
D
PIN ONE REFERENCE 2X 6 4
A
B
E1 0.20 C
2X 1 3
E
0.20 C TOP VIEW 0.10 C A
6X
NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.10 AND 0.15 MM FROM TERMINAL. 4. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. DIM A A3 b D D2 E E1 E2 e L MILLIMETERS MIN MAX 0.70 0.90 0.15 REF 0.20 0.40 2.90 BSC 1.40 1.60 3.00 BSC 2.80 BSC 1.50 1.70 0.95 BSC 0.15 0.25
0.08 C
SEATING PLANE
(A3) SIDE VIEW D2
1
C
e
3
L
6X
E2
6 4
EXPOSED PAD
b BOTTOM VIEW
6X
NOTE 3
0.10 C A B 0.05 C
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative
http://onsemi.com
17
NCP694/D

▲Up To Search▲

Price & Availability of NCP694HSAN33T1G

	To Download NCP694HSAN33T1G Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .